Can I Install A Tub Myself?
Can I Install A Tub Myself?
Blog Article
The author is making a few good annotation related to A Step-by-Step Guide to Installing a Bathtub overall in the article further down.
Installing a bathtub isn't precisely brain surgery, but it does need strong plumbing, woodworking, and in some cases, tiling skills. Changing an old bath tub with a brand-new one is additionally a moderately challenging job. If the old bathtub is conveniently accessible, the job can relocate easily; if you have to open a wall to eliminate the old bathtub and also place the brand-new bathtub, the task is much harder. In either situation, the job is within a residence handyman's abilities, although you will certainly need a helper to move out the old tub as well as embeded in the brand-new one. Make certain you have actually certified on your own for the work and also are comfortable attempting it. Rather than hiring a professional to take over a halfway-completed job, it is much better to think about utilizing one before you begin. Possibilities are you may need an expert plumber to make tube connections.
This post will assist you set up a new tub in your restroom if you have already bought a new tub and also do not require to transform the setup of your previous water system pipelines.
Your devices as well as material checklist should comprise the following:
Getting ready for the Setup
Firstly, the supporting structure provided with the bathroom ought to be fitted (if required) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is necessary to see to it that if the faucet comes with a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps unit to stop pressure on the tub.
Fit the flexible faucet ports to the bottom of the two faucets making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. See to it you utilize all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom should currently be ready to be suited its final placement.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installation, after that the first thing you ought to do is detach the water supply. After doing so, switch on the taps to drain any kind of water staying in the system. The procedure of eliminating the existing faucets can be quite bothersome due to the limited accessibility that is typically the instance.
Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the faucets. Have a fabric all set for the remaining water that will certainly originate from the pipes. When the supply pipelines have been eliminated, make use of the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from turning during this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any old sealing substance.
Prior to moving on to fit the new faucets, contrast the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new taps to fit.
Setting up the Tub
Making use of both wooden boards under its feet, put the tub in the needed setting. The wood boards are helpful in evenly spreading the weight of the bath tub over the location of the boards instead of focusing all the weight onto four little factors.
The following objective is to ensure that the bathtub is leveled all round. This can be achieved by inspecting the level and also readjusting the feet on the bath tub until the spirit level reads level.
To set up taps, fit all-time low of the outermost adaptable faucet adapter to the ideal supply pipe by making a compression join; then do the same for the other tap.
Switch on the supply of water and check all joints and brand-new pipework for leakages as well as tighten them if needed. Fill up the bathtub and also examine the overflow electrical outlet as well as the typical outlet for leakages.
Lastly, repair the bath paneling as described in the supplier's user's manual. Tiling as well as sealing around the bathtub should wait till the tub has been used at the very least when as this will settle it right into its last setting.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end provides a link to the existing supply pipes.
If you require to fit a monobloc, after that you will call for minimizing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, place the tap in the placing opening in the bath/basin guaranteeing that the washing machines remain in area between the faucet as well as the sink. Safeguard the tap in place with the supplier offered backnut. As soon as the faucet is securely in position, the supply pipes can be attached to the tails of the taps. The taps can either be linked by using corrugated copper piping or with regular tap adapters. The former kind must be connected to the faucet ends initially, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the area where the bathroom satisfies the floor tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to split a rigid seal, creating the water to permeate the wall surface in between the bath as well as the tiling, resulting in difficulties with dampness and also possible leakages to the ceiling below.
You can select from a selection of coloured sealants to assimilate your components as well as installations. They are sold in tubes as well as cartridges, and also are capable of securing voids approximately a width of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with spins of soaked paper or soft rope. Bear in mind to always fill up the bath tub with water before sealing, to permit the movement experienced when the tub remains in usage. The sealant can split rather early if you do not take into consideration this activity before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also easily readily available on the market. It is recommended to fit the ceramic tiles making use of water-resistant or waterproof sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We were made aware of that write-up about Installing A Bathtub from an acquaintance on another site. Those who liked our blog post plz make sure you remember to pass it around. We treasure reading our article about Installing A Bathtub.
Request An Appointment
Report this page